Ten Things Everybody Is Uncertain About Kia Picanto Key Fob Replacement > 자유게시판

• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

How to Replace a Repair Kia Key Fob Sportage Replacement Key

The key in many Kia models has a keyless entry system built in. This key is similar to remote controls and can be exchanged by an Kia dealer.

Key fobs may stop working for several reasons, including an empty coin battery, worn buttons water damage, signal interference and a faulty receiver module. Here are some suggestions on how you can get your Kia Sportage replacement key back to working.

How to replace the remote key or smart key

It doesn't matter if your Kia comes with an intelligent key, remote key push to start key, or regular metal non-transponder key, the battery in these keys will eventually require replacement. This is especially relevant if your vehicle displays a message that indicates that the smart or remote key has low battery power.

It's a fairly simple process. To replace the battery on the key fob, remove the mechanical key from the hole in the back of the key fob and pry open the cover. Inside the key fob, there will be an incredibly small screw that holds the battery in its place. With a small screwdriver, take the screw off and remove the old battery. Then, you can insert the new battery and close the slit on the key fob.

When the key fob is equipped with a fresh battery, test it by pressing the locks and unlock buttons. If the doors lock and unlock according to your expectations, then you're all set! You can now use the hands-free feature to lock and unlock your Kia when your fingers get cold or you have to complete errands in Brandon.

Note: Certain key fobs (transponder chip or smart keys) might require their programming done. This requires a specific programming machine that only the dealer or automotive locksmith has access to. Other keys (non-transponder metal keys) don't require programming. If you're looking to reprogramme your key, it is necessary to write down the key code's number on the tag for the key code.

How do I replace the battery?

If the kia spare key key fob doesn't respond to pressing the lock/unlock button, it is likely that the battery is not fully charged. A low battery may cause other issues, like the check engine light coming on or the engine not running correctly. It is fairly easy to replace the key fob batteries using just two tools.

Make sure you turn off your vehicle and close all doors before you begin. Find the small, metal or plastic piece that is located at the bottom of the key fob. Move it until the metal key falls out. This key can be put into the door's driver handle to unlock your car.

To replace the key fob battery, remove the cover at the rear and use a plier bar tool to release the latch that holds the black negative battery cable. Remove the old battery and then orient the replacement battery so that its "+" side is facing you and the "-" negative side is facing the fob's electrical contacts. Avoid using excessive force when pushing the new CR2032 into position to avoid damage or bending the metal contacts.

Once the new battery is installed then turn the key fob off and on in the ignition several times until the door locks cycle. You can then test your Kia's key fob again to make sure it's functioning properly.

How to replace a smart key

You could have a standard keyfob, or a Smart Key, based on the model of Kia Sportage. The difference is that the smart fob has tiny mechanical key blade in it, whereas the standard fob doesn't. Both key fobs have a battery that will eventually require replacing. This is an easy process that takes less than two minutes.

Before you begin it is essential to make sure that you are on a level surface with adequate lighting and that your Kia is not on. Also, remember that there are tiny parts inside the fob which could fall out if you are not careful.

The first step is to find the small release button that is located on the lower backside of the fob. It's either an oval or circular slot. When you press it button, the mechanical blade will pop out and you will be able to open the key fob.

Once you have the key fob opened and you are able to remove the old battery and replace it. The new battery is a one called CR-2032 and can be purchased from a local or online auto parts shop. After you've finished you should be able to lock or unlock your car with your key fob, even if your engine isn't running!

How to replace a mechanical key

The kia rio key replacement keyfob is an excellent convenience, allowing us to lock or unlock our car simply by pressing one button. As with all devices that is used, the Kia key fob can occasionally have problems. Luckily, there are steps to take to solve these issues and ensure that our key fobs are in good working order for the long term.

A dead or weak battery is one of the most common issues. This can cause your fob to stop working or operate intermittently. If this happens try replacing the battery with a fresh new one.

If this isn't enough to resolve the issue you can try using a standard flathead screwdriver to wedge open the fob's plastic casing. Be careful not to damage internal components or scratch the plastic. Once open, carefully remove the battery that was removed and replace it with a new one.

Once the new battery is in, close and then open the doors with the mechanical key (every Kia fob has an emergency mechanical key that can fit in the slot). Test the key fob and make sure it is working correctly. Contact a dealer or a locksmith to solve the issue if the fob is still not working. To avoid a lockout in the future ensure you purchase an emergency key that will work in all of the trunk and door cylinders.